SainSmartTPU Filament 1.75mm, GT-3 Flexible 3D Printer Filament for High-Speed Printing 500mm/s, Blue, 2.2 LBS (1KG) Spool, Dimensional Accuracy +/- 0.04mm

This TPU prints pretty nicely overall but I feel like the temps range may be a bit high in my opinion.Now bare in mind I have a nozzle installed on my printer that is known for reducing the print temp of filaments by usually 10 degrees but with this I was able to reduce it from its lowest of 220 to 200 and get a relatively nice print at 150mms speed and a flow rate of 8. Still need to run a few tests to see if I can match that speed at 190 but I would honestly recommend the company run some tests to see what is the absolute lowest they can run this filament on a corexy cause I think 220 is still a little high at least for this filament.Now before you get this be prepared for a few things.1. Your pressure advance, if you use it, will be high for TPU in general. This one is no exception.2. Higher retraction length is a must. Went from a .4 with pla to 2.3. This filament will ooze for tests like PA4. The extrusion multiplier is gonna be hard to figure out due to the filament being a bit translucent until you get a good few layers on a model.Overall though I would strongly recommend this filament overall

The media could not be loaded. Very easy to use, not hard to print and good quality. Excellent filament for the price

On a Bambulabs P1S, I was able to get pretty great results after doing the flow calibrations and slowing down some of the acceleration parameters. I think this TPU prints a hair less reliably than Overture HS TPU, but I do prefer it to the Bambulabs HF TPU. The Bambulabs seems slightly softer and more difficult to clean up things like zseams and stringing.A note - at least in the blue color this is more of a translucent filament, it's not perfectly opaque. It's similar to the look of the Overture HS TPUs that are labeled "translucent."

Good prints at a reasonable speed. Minimal stringing at 230C. Finally a TPU that gives decent prints. Only downside is it is a little bit harder than the 95A normal Sainsmart TPU. I only get the slightest whisper of stringing, like a few strands of a cob web. Print surface is quite clean - if dried at 65C.

Prints faster than normal TPUs but not as fast as other HS/HF TPUs, and isn't dimensionally accurate. Comes vacuum sealed but still to wet to print with. 6 hours in the dryer, still too wet. Dried overnight, then it's printable, but my extrusion benchmarks are all over the place because filament diameter isn't consistent. You can look at it an tell it's not round, looks like it's made on the same extrusion line as weed trimmer line.

Good TPU, fun color. I still print it low and slow even though this is marketed as being higher speed. It works well with my normal TPU setup and I'm happy not messing with that. My only knock on this really is the price being around 50% more than other TPU that prints consistently well.

This thing prints great for me right out of the box on my P1S, had to tweak settings based on the review here. Temperature to 236C, flow rate 14 mm3/s and it print fast and with almost no stringing. Dried it for 4 hrs before use just in case. Will for sure buy again

The translucent green TPU is the best printing TPU I've used, and I highly recommend it.I dried the filament for four hours after taking it out of the box, placed it in a dry box for storage for a day or so, and then hooked it up to my Bambu Lab A1 to print a filament sample card. Using the Bambu Studio "Generic TPU" setting, the result was impeccable. The print quality rivals PLA in terms of sharpness. No stringing at all, top surface excellent, letters sharp and clear. The translucency is excellent, with the single-layer sample appearing virtually clear (excepting for the pattern from the textured build plate).Next, I printed some vise jaw pads I designed. This time, I selected the "Bambu Lab TPU 95A HF" profile. In my experience, "high speed" TPUs usually print well enough with this profile. Using the generic profile, this model would've taken over four hours to print; with the Bambu profile, just under two hours. Again, an impeccable print with smooth walls and no stringing. I'll have to experiment, I suspect that functional prints can be pushed even faster with this filament.And the green is a beautiful electric lime.I've used TPU from Bambu Lab, Overture, GIANTARM, ERYONE, and Hatchbox. The SainSmart GT-3 easily outshines all of them.

Se rompe muy fácil dentro del extrusor aún con los mejores parámetros a la hora de imprimir

Después de meterlo en la deshidratadora a 50° durante 10h es perfecto, antes no...muchos hilos y burbujas.Uso una bambulab y ni flipando subes de 150mm/s.. en rellenos, en perimeteos subir de 40mm/s es jugarsela. Supongo que los almacenes tienen humedad.

Ottimo TPU se si vuole stampare velocemente.Non ho avuto tempo di calibrare il filamento con vari test perchè avevo un lavoro urgente da consegnare.Con una Bambu P1S ho stampato l'oggetto in foto a 200-250 mm/s in 9 ore con altezza layer 0.24 e infill 25%... pazzesco...appena lo calibrerò avrò risultati migliori anche se in effetti non mi interessano più di tanto, soprattutto per oggetti cosi grandi.Sono rimasto molto soddisfatto visto le velocità che ho usato.Se il prodotto avesse un prezzo di un pelo inferiore sarebbe il best buy

TPU de bonne qualité, mais absolument pas compatible haute vitesse !Testé sur K1 Max, Même à 80mm/s ne fonctionne pas, d'où ma déception.En utilisant le parametre de TPU générique, ca marche et donne de belles pièces, mais c'est limité à 30mm/s environ.

Le produit est annoncer en livraison Prime, mais une fois la commande validé, le produit est livré en décembre. Nous sommes en juin.Pour avoir déjà essayer Le produit, il est de très bonne qualité